DYSON DC04 PROBLEM SOLVING

Built to last All Dyson products go through extensive testing and checks for guaranteed quality. But fitting it is not really an amateur job. Jennifer MacArthur on March 7th, at 8: If the machine has no suction at the lower hose, you must check the carriage mechanism where the valve cover lifts out from to make sure it is switching over when the machine is reclined. Occasionally it will if you hold the handle at a certain angle. There is suction from the bottom, but only limited pick up due to the brush bar not turning. This was partly due to the brush roller end cap plastic drive dogs being extremely worn.

If you prefer to change the belt, they are here: This has served ok but recently I notice that the vacuum seems to stick to the floor due to too much suction at the base, whether on carpet or hard floor. Dyson Spares – The Dyson Forums. If I pull the soleplate front down again, it works fine until it pops back up. This entry was posted on Sunday, February 13th, at

I have a Dyson DC07 and the brush is not spinning when reclined. DC11 – Remove the cyclone and bin, wash the rectangular filter immediately visible, DC14 – wash the filter above the bin in the cyclone top.

Welcome to Dyson

Suction problems are mainly due to blockages or dirty filters. The only course of action is to replace the entire filter if your suction is good when the filter is removed. Dyson vacuum cleaner – Suction problems troubleshooting tips. DC11 – Remove the cyclone and bin, wash the rectangular filter immediately visible, DC14 – wash the filter above the bin in the prooblem top.

It worked Ok for six months or so until it began to sound like a very large and powerful tractor. Hello, and thank you for all the helpful advice!

  GUIDED READING TOTALITARIANISM CASE STUDY STALINIST RUSSIA ANSWERS

dyson dc04 problem solving

I am quite happy to do that, but before doing so, I just thought I should check whether there is anything else I should check or do first. DC02 two rectangular filters visible djson the cyclone top is opened. I have taken it apart and cleaned all the dog hair out of the usual places. It also sometimes makes a loud clicking noise.

The Brush Roll Won’t Turn – Dyson DC04, Dyson DC07 and Dyson DC14

Occasionally it will if you hold the handle at a certain angle. Explore the lightweight range of Dyson cordless vacuums.

DC14, brush roller not being driven.

Removing the filters to test the suction does not always work! Full size vacuums Upright corded vacuums engineered to clean across all floor types. This is a new feature for so we are in the process of adding new videos monthly so if your model isn’t available yet then check back or drop us an email. How do i fit a drive belt to my yellow dyson 04, it is encased where the belt is supposed to be threaded through.

dyson dc04 problem solving

If I pull the soleplate front down again, it works fine until it pops back up. So I removed the brush bar, pulled both ends off to find they were both full of hair and dirt. Also, you know the machine will only suck from the cleaner head when it is reclined, yes? Is there a solution other than chucking the whole thing in the garbage? I cleaned the filter, cleaned the brush, checked all the connections for blockage, and I even just replaced the clutch. I removed this and even popped the plastic off the end of the bearings.

  DISSERTATION LUTILISATION PRIVATIVE DU DOMAINE PUBLIC

Check the hose all the way along for splits and tears usually they start under the top cuff but check the entire hose just in case If the hose has a small tear in it and it is not fully stretched out then you are not going to lose massive amounts of suction, it will need replacing but don’t buy a hose until you figure out what else is causing the loss in suction.

Solviny will be coming soon as I understand this is hard to follow. Angus Black on July 6th, at 4: Great article and thank you for taking the time to post it. You want either a new clutch or a clutch refurb. I have taken the roller out and checked for blockages on the roller and edges but as I say it is new, so it is hardly dirty. DC22 – Looking at the Dyson from the front turn it onto its right hand side, Use a coin to open the 2 blue screws and remove the rectangular HEPA filter.

What you have there is a broken loom in the hinging mechanism.

The Brush Roll Won’t Turn – Dyson DC04, Dyson DC07 and Dyson DC14

It worked Ok for six months or so until it began to sound like a very large and powerful tractor. DC33 – Dyyson at the Dyson from the front, wash the filter at the bottom right of the machine and also the HEPA filter underneath the bin.

I have changed the clutch but the motor belt keeps slipping off the motor spindle.